Technical cost modelling for a generic 45-m wind turbine blade produced by vacuum infusion (VI)SCHUBEL, P. J.Renewable energy. 2010, Vol 35, Num 1, pp 183-189, issn 0960-1481, 7 p.Article

Sustainable vacuum-infused thermoplastic composites for MW-size wind turbine blades-preliminary design and manufacturing issuesVAN RIJSWIJK, K; JONCAS, S; BERSEE, H. E. N et al.Journal of solar energy engineering. 2005, Vol 127, Num 4, pp 570-580, issn 0199-6231, 11 p.Conference Paper

Design and testing of joints for composite sandwich/steel hybrid ship hullsJUN CAO; GRENESTEDT, Joachim L.Composites. Part A, Applied science and manufacturing. 2004, Vol 35, Num 9, pp 1091-1105, issn 1359-835X, 15 p.Article

Cost reduction in manufacturing of aerospace compositesVAN HATTUML, F. W. J; REGEL, F; LABORDUS, M et al.Plastics, rubber and composites. 2011, Vol 40, Num 2, pp 93-99, issn 1465-8011, 7 p.Conference Paper

Bubble free resin for infusion processAFENDI, Md; BANKS, W. M; KIRKWOOD, D et al.Composites. Part A, Applied science and manufacturing. 2005, Vol 36, Num 6, pp 739-746, issn 1359-835X, 8 p.Article

Double cantilever beam Mode-I testing for vacuum infused repairs of GFRPTZETZIS, D; HOGG, P. J; JOGIA, M et al.Journal of adhesion science and technology. 2003, Vol 17, Num 3, pp 309-328, issn 0169-4243, 20 p.Article

Effects of fibers' alkali treatment on the resin transfer molding processing and mechanical properties of jute-vinylester compositesRODRIGUEZ, Exequiel S; STEFANI, Pablo M; VAZQUEZ, Analia et al.Journal of composite materials. 2007, Vol 41, Num 14, pp 1729-1741, issn 0021-9983, 13 p.Article

Optimisation of anionic polyamide-6 for vacuum infusion of thermoplastic composites : Influence of polymerisation temperature on matrix propertiesVAN RIJSWIJK, K; BERSEE, H. E. N; BEUKERS, A et al.Polymer testing. 2006, Vol 25, Num 3, pp 392-404, issn 0142-9418, 13 p.Article

Analysis of the vacuum infusion moulding process: I. Analytical formulationCORREIA, N. C; ROBITAILLE, F; LONG, A. C et al.Composites. Part A, Applied science and manufacturing. 2005, Vol 36, Num 12, pp 1645-1656, issn 1359-835X, 12 p.Article

Temperature Evolution During Processing of Thick-Walled Anionic Polyamide 6 Composites: Experiment and SimulationTEUWEN, Julie J. E; GEENEN, Ab A. Van; BERSEE, Harald E. N et al.Macromolecular materials and engineering (Print). 2013, Vol 298, Num 7, pp 722-729, issn 1438-7492, 8 p.Article

Development of the double RIFT diaphragm forming processCHANNER, K. J; COSGRIFF, W; SMITH, G. F et al.Journal of reinforced plastics and composites. 2002, Vol 21, Num 18, pp 1629-1635, issn 0731-6844, 7 p.Article

Characterization of composites based on natural and glass fibers obtained by vacuum infusionRODRIGUEZ, Exequiel; PETRUCCI, Roberto; PUGLIA, Debora et al.Journal of composite materials. 2005, Vol 39, Num 3, pp 265-282, issn 0021-9983, 18 p.Article

Analysis of pressure profile and flow progression in the vacuum infusion processMODI, Dhiren; JOHNSON, Michael; LONG, Andrew et al.Composites science and technology. 2009, Vol 69, Num 9, pp 1458-1464, issn 0266-3538, 7 p.Conference Paper

Mechanisms controlling particle distribution in infusion molded compositesFERNBERG, S. P; SANDLUND, E. J; LUNDSTRÖM, T. S et al.Journal of reinforced plastics and composites. 2006, Vol 25, Num 1, pp 59-70, issn 0731-6844, 12 p.Article